Siemens 6FX8002-2DC10-1AJ0 Pre-Assembled Signal Cable
Product Introduction
The Siemens 6FX8002-2DC10-1AJ0 delivers reliable communication for DRIVE-CLiQ-based drive systems. This pre-assembled signal cable belongs to the MOTION-CONNECT 800PLUS product line. It connects a controller or drive module to a motor in tough industrial settings. On the module side, you will find an RJ45 connector with a 24 V plug rated IP20. On the motor side, the connector achieves IP67 protection.
Furthermore, Siemens limits this cable series to a maximum approved length of 75 m. The model 6FX8002-2DC10-1AJ0 comes with a fixed length of 8 m. Its outer diameter measures only 7.1 mm, which saves valuable space in cable ducts and panels. Because it comes pre-assembled, you avoid field wiring errors and reduce installation time significantly.
Technical Specifications
Cable type: DRIVE-CLiQ signal cable with integrated 24 V supply
Connector (module side): RJ45, IP20, includes 24 V plug
Connector (motor side): IP67 rated, resistant to dust and water jets
Motion-Connect standard: 800PLUS (high flexibility for bending and torsion)
Maximum approved length for series: 75 m
Actual length (m): 8 (tolerance: +0 / +0 / +8 / +0)
Outer diameter (Dmax): 7.1 mm
Net weight: 0.573 kg per piece
Packaging quantity: 1 piece
Country of origin: Slovakia
Commodity code: 85444290
EAN: 4042948664544
UPC: 662643238969
Mechanical & Environmental Parameters
This cable handles demanding industrial environments with ease. MOTION-CONNECT 800PLUS ensures excellent resistance to oil, coolants, and mechanical stress. Use it in drag chains or robotic applications that require continuous bending. The IP67 rating on the motor side makes it suitable for washdown areas, dusty floors, or outdoor enclosures.
Meanwhile, the IP20 module side stays protected inside a control cabinet. Only basic protection against accidental contact is needed there. The cable's small bending radius follows Siemens standard DRIVE-CLiQ specifications. For dynamic applications, always observe the minimum bend radius to maximize service life.
Installation Guidelines
First, check the required distance between your drive and motor. The Siemens 6FX8002-2DC10-1AJ0 provides exactly 8 m of length. Next, inspect both connectors for any shipping damage before installation. Plug the RJ45 with the 24 V supply into the DRIVE-CLiQ socket on the module side. Then, push and twist the IP67 connector on the motor side until it locks securely.
Additionally, route the cable away from sharp edges and hot surfaces. Use proper cable trays with smooth radii. For moving cable applications, follow the bending and torsion limits defined in the MOTION-CONNECT 800PLUS documentation. Finally, avoid pulling the cable by the connectors. Always grip the cable body when adjusting slack.
Packaging List
1 x Pre-assembled signal cable 6FX8002-2DC10-1AJ0 (8 m length)
1 x RJ45 connector with 24 V plug (module side, factory-attached)
1 x IP67 connector (motor side, factory-attached)
*Note: Certificates and 12-month warranty documents are not included in the package. Shipping method: Fedex, UPS, DHL.*
Frequently Asked Questions (FAQ)
1. Can I extend the 6FX8002-2DC10-1AJ0 beyond its 8 m length?
No. Siemens does not recommend extending this pre-assembled cable. Signal integrity and 24 V power delivery depend on factory-terminated ends. Order a longer variant from the same series instead.
2. What happens if I use this cable beyond the 75 m limit?
The DRIVE-CLiQ communication may become unstable. Siemens approves the entire MOTION-CONNECT 800PLUS series only up to 75 m. Longer distances risk data loss and drive faults.
3. Is the 24 V plug on the module side replaceable?
No. The 24 V supply is integrated into the RJ45 housing. You cannot replace it separately. If damaged, replace the entire Siemens 6FX8002-2DC10-1AJ0 cable.
4. Can I use this cable for static applications only?
Yes, but MOTION-CONNECT 800PLUS also supports dynamic use. For static installations, you can choose lower-cost cables. However, this 800PLUS version provides extra durability for future upgrades.
5. Which Siemens controllers are compatible with this cable?
This cable works with SINAMICS S120 drive modules and SINUMERIK 840D sl CNC systems. Any device with a DRIVE-CLiQ interface accepts this pre-assembled signal cable.
