The Bently Nevada 177230-00-01-05 seismic transmitter measures vibration velocity in rotating machinery. You can use it with PLCs, DCS, or SCADA systems that have current-limited internal power supplies. This device converts RMS vibration levels into a standard 4-20 mA signal. Therefore, it integrates easily into existing monitoring systems.
The 177230-00-01-05 offers a measurement range of 0 to 12.7 mm/s (0 to 0.5 in/s). Its frequency response spans 10 Hz to 1 kHz (±10%), which equals 600 to 60,000 cps. This model provides an RMS (Root Mean Square) output rather than peak values. The main loop sensitivity shows 4 ±0.3 mA at 0.0 mm/s and 20 ±2 mA at full scale. Settling time stays under 15 seconds within 2% of final value. Additionally, the mounted resonant frequency exceeds 12 kHz. Transverse sensitivity is less than 5% of sensitivity.
For electrical requirements, this sensor needs an excitation voltage of 12 to 30 Vdc, current limited to 40 mA. Typically, host systems limit current between 30 mA and 35 mA. The sensing element uses a ceramic/shear design. Electrical isolation is greater than 10⁸ ohms, and breakdown voltage reaches 600 Vrms with less than 1 mA leakage.
The case material is 316L stainless steel, which resists corrosion effectively. Diameter measures 25.4 mm (1.00 in), and height is 66.0 mm (2.60 in). Weight is 0.131 kg (4.62 oz). The connector is a 3-pin MIL-C-5015, also made of 316L stainless steel.
Mounting options include a ¼-28 UNF hole in the body. Other available threads are M6 X 1 SI and M8 x 1.25 SI. You should apply a mounting torque of 4 to 7 N-m (35.4 to 62.0 in-lbf). Operating temperature ranges from -40°C to +85°C (-40°F to +185°F). The transmitter handles relative humidity up to 100% non-submerged. Shock survivability is 9.810 m/s² (1.000 g peak) for a drop test. Magnetic field sensitivity stays below 20 μm/s/gauss peak.
This particular model uses a 10 Hz to 1 kHz frequency response with RMS detection. Many other Bently Nevada seismic transmitters use 3 Hz to 1 kHz with peak detection. Therefore, the 177230-00-01-05 suits applications where RMS values are preferred. RMS provides a better representation of overall energy in the vibration signal.
This product is hermetically sealed, so it resists moisture and contamination. Its high resonant frequency avoids mechanical interference. Moreover, the low transverse sensitivity reduces measurement errors. The multiple approvals (CSA/NRTL/C, ATEX/IECEx) make it suitable for hazardous areas.
Compared to other sensors, the 177230-00-01-05 offers simple two-wire loop power. You do not need separate signal conditioners. As a result, installation costs stay lower. Many engineers prefer this model for fans, pumps, compressors, and general machinery monitoring where RMS readings are standard.
1. What is the difference between the 177230-00-01-05 and the 177230-01-02-05?
The 177230-00-01-05 has a 0-12.7 mm/s range and 10 Hz to 1 kHz RMS output. The other model uses 0-25.4 mm/s range with 3 Hz to 1 kHz peak output.
2. Can I use this transmitter with a 24V PLC analog input card?
Yes, you can. Most PLC analog input cards accept 4-20 mA signals. Ensure the card provides a current loop supply in the 30-35 mA range.
3. Why does this model use RMS instead of peak detection?
RMS provides a measure of the average energy in the vibration signal. Many industrial standards specify RMS for overall machine vibration monitoring.
4. Is the dynamic signal on Pin C isolated from the loop?
No, the dynamic signal references Pin B (loop return). Do not ground Pin B at more than one point.
5. Can this transmitter be submerged?
No. It handles 100% relative humidity but only in non-submerged conditions. Do not immerse it in liquid.
| Brand Name | Bently Nevada |
| Model No. | 177230-00-01-05 |
| Product Type | Seismic Transmitter |
| hasMerchantReturnPolicy | Adjust according to reality |
| Shippingdetails | Adjust according to reality |
