GE IC660BBD023 24V Sink I/O 16 Circuit Block

GE IC660BBD023 Genius I/O Block

Product Introduction

The IC660BBD023 functions as a Sink I/O block within the GE Genius I/O series. GE Fanuc originally designed this module for the Series 90-30 PLC system. It supports 16 discrete circuits, and you can configure each one independently as an input, output, or tristate input. This block works seamlessly with 2-wire and 3-wire solid-state sensors as well as electromechanical sensors. Moreover, it provides comprehensive diagnostic features including short circuit, over-temperature, and open wire detection. The Genius protocol ensures reliable communication with the master controller.

Key Technical Specifications

The IC660BBD023 operates on a nominal voltage of 24 VDC. Each circuit delivers a steady-state output current up to 2 Amperes. The output OFF leakage current is 1.9 milliamperes. The selectable input filter time ranges from 10 to 100 milliseconds. Heat dissipation reaches 68.8 Watts when operating with 2 Amperes across all 16 outputs.

The module measures 22.4 cm x 9.05 cm x 11.23 cm (8.82 x 3.56 x 4.42 inches). It weighs approximately 1.8 kg (4 lbs). The operating temperature range is 0 to 60 degrees Celsius.

Input and Output Characteristics

Input channels on the IC660BBD023 accept 24 VDC nominal voltage. The block receives current from field output devices. For wiring terminals, use #12 wire or two #14 wires. The front panel includes LED indicators that show the status of the unit and the I/O activity. These indicators help you monitor operation at a glance.

Configuration Features

The IC660BBD023 offers several configurable parameters. These include output pulse test capability, configurable input filter time (10-100 ms), output power-up defaults, and output hold last state or default. No additional components are required for configuration. A handheld monitor and CPU revision 110 or later are necessary for proper configuration. This block works with all types of handheld monitors.

Diagnostic and Protection Features

The IC660BBD023 includes comprehensive diagnostic and protective capabilities. It monitors for short circuits, over-temperature, failed switch conditions, overload, and open wire detection. The block detects installation problems and runtime errors effectively. When an issue occurs, the block reports it to a handheld monitor and takes appropriate corrective action. These features significantly reduce troubleshooting time and improve system reliability.

Compatibility and Replacement

The IC660BBD023 can replace all its previous versions when you connect a compatible electronics assembly. For internal communication, the block has Serial Port 1 and Serial Port 2. It also includes a Shield In port and a Shield Out port. You can configure or monitor the I/O block by using a programmable controller connected to the monitor port.

Mechanical and Environmental Parameters

The IC660BBD023 measures 8.83 inches (22.4 cm) in height, 3.56 inches (9.05 cm) in width, and 4.42 inches (11.23 cm) in depth. The operating temperature range is 0 to 60 degrees Celsius. This block meets UL standards and complies with various industrial standards. It has open architecture and should be protected against water splashes, dust, and airborne contaminants. For indoor use only.

Installation Guidelines

First, install the IC660BBD023 inside a protective case. The installation area must be clean and free of airborne contaminants. Adequate cooling and airflow are essential for proper operation. A reliable grounding system is also required. You can mount the block right-side up or upside down.

When replacing an electronics assembly, exercise caution due to the risk of electrical shock. Always disconnect circuit power before disconnecting block power. To replace an assembly, first connect a handheld monitor. Monitor the circuits from the HHM menu, then turn it off and disconnect. Power down the block, remove the old electronics assembly, and install the new one.

Packaging List

• IC660BBD023 Sink I/O block (1 unit)

• Mounting screws with star washers

• Quick start guide

Note: No certificates or warranty documents are included.

Shipping Information

We ship worldwide via FedEx, UPS, or DHL. All packages include tracking and proper anti-static protection.

Frequently Asked Questions (FAQ)

1. Can the IC660BBD023 work with 2-wire sensors?
Yes, the IC660BBD023 is specifically compatible with both 2-wire and 3-wire solid-state sensors. Each circuit supports these wiring types without needing additional components.

2. What is the selectable input filter time range?
The IC660BBD023 allows you to select input filter times between 10 milliseconds and 100 milliseconds. This flexibility helps you match the block to your specific application requirements.

3. What happens during an overload condition?
The IC660BBD023 detects the overload immediately. Its protective mechanism takes appropriate action, and the block reports the error to the handheld monitor.

4. What handheld monitor is required for configuration?
The IC660BBD023 works with all types of handheld monitors. However, you need CPU revision 110 or later for proper configuration.

5. What is the heat dissipation of this block?
The IC660BBD023 dissipates 68.8 Watts of heat when operating with 2 Amperes across all 16 outputs. Ensure adequate cooling airflow around the block during installation.