The Bently Nevada 330901-00-10-05-02-00 is a precision-engineered sensor from the renowned 3300 NSv series. This model features a 1/4-28 UNF threaded case without armor, offering a compact and lightweight solution for proximity measurement. Its total length reaches just 0.5 meter (20 inches), making it perfect for installations with limited space or where only a short cable run is needed. Additionally, this probe includes a miniature coaxial ClickLoc connector with standard cable. It delivers accurate, non-contact vibration and position monitoring for a wide range of rotating machinery, including turbines, compressors, and pumps.
The 330901-00-10-05-02-00 probe is built for reliable performance in demanding industrial environments. Its case uses AISI304 stainless steel (SST) , providing excellent corrosion resistance and durability. The probe tip is manufactured from polyphenylene sulfide (PPS) , ensuring long-term wear resistance and reliable operation. The cable is a 75 Ω coaxial type with fluoroethylene propylene (FEP) insulation, which maintains signal integrity even in harsh conditions with chemical exposure or high temperatures. For this 0.5-meter version, the DC resistance from the center conductor to the outer conductor (RPROBE) is 4.0 ± 0.5 ohms. Furthermore, a Viton O-ring seals the probe to manage differential pressure between the tip and case, though these units are not pressure tested prior to shipment.
This sensor operates effectively across a wide temperature spectrum. Its operating and storage temperature ranges are both from -52°C to +177°C (-62°F to +351°F) . However, prolonged exposure below -34°C (-30°F) can lead to premature seal failure, so careful attention to ambient conditions is essential. The probe weighs approximately 14 to 150 grams (0.5 to 5.3 oz), with the shorter cable making this model one of the lightest in the series. For installation, the recommended torque for 1/4-28 or M8X1 probe cases is 5.1 N•m (45 in•lb) , while the maximum rated torque is 7.3 N•m (65 in•lb). The maximum length of thread engagement is 0.375 inches, which should be carefully observed to prevent damage.
The Bently Nevada 330901-00-10-05-02-00 offers significant benefits due to its short 0.5-meter cable length and compact 1.0-inch overall case. This compact design minimizes cable management requirements and reduces the risk of cable damage during installation. Consequently, this model is particularly well-suited for retrofitting existing machinery where space around the measurement point is limited. Additionally, the shorter cable reduces overall system cost and simplifies troubleshooting, as there are fewer connection points to inspect. The absence of armor further enhances flexibility, allowing easier routing in tight spaces and reducing overall weight.
Proper installation of this 3300 NSv probe ensures optimal performance and long service life. First, thoroughly clean the mounting surface and inspect the 1/4-28 UNF threads for any damage or debris. Then, hand-tighten the probe into its housing until it feels snug. Next, use a torque wrench to apply the recommended torque of 5.1 N•m (45 in•lb) to the probe case. Since this model lacks armor, handle the cable gently to prevent kinking or crushing during installation. Additionally, set the correct air gap according to your specific application requirements, typically using a feeler gauge or dial indicator. Finally, securely fasten the miniature coaxial ClickLoc connector to the extension cable or Proximitor sensor. For best results, route the cable away from high-voltage lines and sources of electromagnetic interference.
This 330901-00-10-05-02-00 probe meets various temperature classifications for hazardous area applications. For EPL Ga and Gc, it covers T1 through T5 classifications with ambient temperature ranges from -55°C up to +232°C. For EPL Dc, it offers T280°C down to T90°C classifications based on ambient temperature. The "00" agency approval option indicates that no specific country approval is required for this model. Nevertheless, it complies with FCC Part 15, EMC Directive 2014/30/EU, and RoHS Directive 2011/65/EU. Therefore, this probe is ready for deployment in most industrial facilities worldwide without additional regional certification requirements.
1 x Bently Nevada 330901-00-10-05-02-00 3300 NSv Proximity Probe (0.5m cable)
1 x Basic installation instruction sheet
Shipping Method: FedEx, UPS, DHL
1. What is the cable length of the Bently Nevada 330901-00-10-05-02-00?
This model features a total length of 0.5 meter (20 inches) , as indicated by the "05" in the product number. This is the shortest option available in the 3300 NSv series.
2. What is the recommended installation torque for this probe?
For the 1/4-28 UNF thread, the recommended torque is 5.1 N•m (45 in•lb) , with a maximum rated torque of 7.3 N•m (65 in•lb). Always use a torque wrench for accurate application.
3. Does this 3300 NSv probe include armor protection?
No, the 330901-00-10-05-02-00 is specified without armor. This makes it lighter and more flexible, which is beneficial for installations with limited space.
4. What is the maximum thread engagement length for this probe?
The maximum length of thread engagement for the 1/4-28 thread is 0.375 inches. Exceeding this limit may damage the probe or mounting hardware.
5. Is the 330901-00-10-05-02-00 suitable for hazardous area use?
Yes, this probe meets multiple temperature classifications for EPL Ga, Gc, and Dc environments. It covers T1 through T5 classifications, making it suitable for various hazardous locations with appropriate temperature ratings.
| Brand Name | |
| Model No. | 330901-00-10-05-02-00 |
| Product Type | Proximity Probes |
| hasMerchantReturnPolicy | Adjust according to reality |
| Shippingdetails | Adjust according to reality |
