The Vibro-Meter CA901 provides reliable vibration data under the most intense industrial conditions. This model (144-901-000-282) features an integrated 3.5-meter cable (designated by the "82" suffix) and a Lemo connector. The sensor produces a charge output with a nominal sensitivity of 10 pC/g. It complies with major nuclear and industrial standards, including NRC guide 1.133 and IEEE 323-1974. Furthermore, the unit features integral case insulation to prevent ground loops. Therefore, the Vibro-Meter CA901 remains a critical choice for high-integrity monitoring in extreme thermal environments.
This accelerometer thrives where standard electronics fail. It operates continuously between -54°C and +650°C. It even withstands extreme peaks from -196°C to +700°C. The housing uses Inconel 600 and features hermetic welding for maximum durability. Additionally, the CA901 offers exceptional radiation resistance. It handles gamma flux up to $10^{11}$ erg/g and neutron flux up to $10^{18}$ $n/cm^2$ without performance loss. Consequently, the sensor provides stable monitoring inside nuclear containment areas and high-pressure steam lines.
The Vibro-Meter CA901 delivers a flat frequency response (±5%) from 3 Hz to 2800 Hz. The sensor detects vibration levels from 0.001 g up to 200 g peak. It also handles an overload capacity of 500 g for transient spikes. To ensure signal purity, the internal insulation resistance exceeds $10^9$ Ω. Furthermore, the unit holds ATEX certification for use in explosive atmospheres (Zones 0, 1, and 2). Therefore, the hardware provides clean vibration data in hazardous or high-interference locations.
The Vibro-Meter CA901 is a passive piezoelectric device. It requires no external input power. Instead, it generates a charge signal proportional to the sensed acceleration. You must process this signal using a dedicated charge converter or signal conditioner. The sensor head features a high resonance frequency of over 17 kHz. This ensures that internal mechanical interference does not affect the operating range. These specifications make the CA901 essential for detecting structural defects or loose components in high-speed machinery.
Mount the Vibro-Meter CA901 inside a tube or to the machine surface using 4 Allen M6 screws. Apply a fastening torque of 15 Nm to ensure a rigid mechanical path. This specific version features a 3.5-meter integral cable, which is ideal for close-proximity connections to a junction box. The total weight is approximately 0.82 kg. Finally, the Lemo connector provides a secure, vibration-resistant interface for connection to your monitoring system.
First, inspect the mounting location. The surface must be clean and flat to support the 17 kHz resonance frequency. Secure the Vibro-Meter CA901 using the 4 Allen M6 screws and tighten them to 15 Nm. Next, route the 3.5-meter cable carefully to avoid high electromagnetic noise. Connect the Lemo connector to your charge converter. Furthermore, secure the cable with clamps to prevent fatigue from constant vibration. Finally, check the output on your diagnostic terminal to verify that the sensitivity aligns with the factory 10 pC/g specification.
1 x Vibro-Meter CA901 Accelerometer (144-901-000-282)
1 x Integrated 3.5-Meter Cable with Lemo Connector
1 x Factory Calibration Certificate
Shipping Carrier: Fedex, UPS, DHL
Q: What is the primary use case for the CA901?
The Vibro-Meter CA901 is specifically designed for loose part monitoring and high-temperature vibration sensing in nuclear and power plants.
Q: Does this sensor require an external power supply?
No. It is a passive piezoelectric device. However, you must use a charge converter to translate the pC signal into a usable voltage or current.
Q: Can this sensor handle cryogenic temperatures?
Yes. With an extreme lower limit of -196°C, the CA901 is fully operational in liquid nitrogen environments.
Q: Is the sensor head protected against moisture?
Yes. The Inconel 600 housing is hermetically welded. This provides a moisture-proof and gas-tight seal for high-pressure environments.
Q: What does the "282" in the part number signify?
The "82" suffix indicates a 3.5-meter cable length with a VM Lemo connector.
| Brand Name | Vibro-Meter (Meggitt) |
| Model No. | Vibro-Meter CA901 144-901-000-212 |
| Product Type | Piezoelectric Accelerometer |
| hasMerchantReturnPolicy | Adjust according to reality |
| Shippingdetails | Adjust according to reality |
