Allen-Bradley 1606-XLP95E 95W Power Supply

1606-XLP95E 24V DC 95W DIN Rail Supply

Product Introduction

The 1606-XLP95E belongs to the Allen-Bradley Bulletin 1606-XL series of compact switched-mode power supplies. Engineers and panel builders choose this unit for its space-saving design and dependable 24V DC output. Specifically, it provides 95W of regulated power for industrial control circuits, sensors, and small automation devices.

This power supply accepts single-phase AC input with manual voltage selection. You can set it for 100-120V AC or 220-240V AC nominal input. The output voltage is adjustable from 24V DC to 28V DC through a front-panel potentiometer. Therefore, it adapts easily to different load requirements in the field.

Technical Specifications

The 1606-XLP95E delivers a nominal 24V DC output with 3.9A at 24.5V, which equals 95W of rated power. Efficiency reaches a typical 90%, reducing heat generation inside enclosures. This power supply does not include a power boost feature, so the output current stays steady under normal load conditions.

Input voltage selection is manual. The terminal block accepts 100-120V AC or 220-240V AC single-phase input. For instance, you must set the selector switch to match your local mains supply before powering the unit. This prevents damage and ensures correct operation.

The unit is rated NEC Class 2, which means the output circuit meets specific safety limits for voltage and current. Moreover, it carries UL 60950-1, cUL, and CE marks under the Bulletin 1606 series standard. These approvals support deployment in North American and European markets.

Mechanical and Environmental Parameters

The 1606-XLP95E measures 75mm high × 73mm wide × 103mm deep at the unit body. It weighs 0.36 kg, so it adds minimal load to DIN rails or wall panels. The housing carries an IP20 protection rating, offering finger-safe protection against accidental contact.

Operating temperature starts at -10°C; the upper limit is not published numerically on the product page. Storage temperature starts at -40°C, with the upper bound also unpublished. Relative humidity should stay below 95% non-condensing. Therefore, install the unit in ventilated areas that avoid condensation.

Installation Guide

Mounting is straightforward. The 1606-XLP95E supports both DIN rail and wall mounting. First, snap the unit onto a standard 35mm DIN rail until the latch clicks. Alternatively, use the wall-mounting slots with screws for panel fixation.

Connection uses spring clamp terminals. Insert stripped wire ends into the terminal openings and push the clamp lever closed. No screwdriver torque is needed for the clamping action, which speeds up wiring. Furthermore, the spring clamps resist vibration better than screw terminals in high-shock environments.

Before energizing, verify the manual voltage selector matches your AC supply. Then check output polarity and confirm the load rating stays within 3.9A at 24V DC. Finally, adjust the output potentiometer between 24V DC and 28V DC if your devices need higher voltage. Keep the unit clear of obstructions for adequate convection cooling.

Packaging List

• 1 × 1606-XLP95E power supply unit

• 1 × Installation instruction sheet

• 1 × DIN rail mounting clip (pre-installed)

• 1 × Terminal cover set

• 1 × Anti-vibration packing insert

Shipping is available via Fedex, UPS, and DHL. Orders typically ship within 3–5 business days after payment confirmation.

FAQ

Q1: What output current does the 1606-XLP95E provide?
A: The unit supplies 3.9A at 24.5V, totaling 95W. Output voltage is adjustable from 24V DC to 28V DC.

Q2: How do I select the input voltage?
A: You set the manual selector switch to either 100-120V AC or 220-240V AC. Always confirm the setting before applying power.

Q3: Does this power supply support DIN rail mounting?
A: Yes, the 1606-XLP95E mounts on standard DIN rail and also supports wall mounting with screws.

Q4: What is the protection rating of the housing?
A: The housing carries an IP20 rating. It provides finger-safe protection and suits installation inside control cabinets.

Q5: What approvals does the 1606-XLP95E carry?
A: It holds UL 60950-1, cUL, and CE approvals, plus an NEC Class 2 rating under the Bulletin 1606-XL series standard.