KEB 13F5A3D-YA0H F5 Drive 400V 8.3kVA

KEB 13F5A3D-YA0H Inverter for HOLZMA Beam Saws

Product Introduction

The KEB 13F5A3D-YA0H belongs to the reliable F5 Combivert Axis Drive Series. This inverter handles tough industrial environments with ease. It works perfectly with HOLZMA beam saw models such as the HPL380, HPP350, and 180. Therefore, you can expect better motor control and consistent power conversion. Additionally, this drive supports both North American and European power standards. Its three-phase AC input accepts up to 400V at 50 or 60 Hz. For UL-rated applications, the input voltage reaches 480V with a current rating of 15.4 A. The KEB 13.F5.A3D-YA0H also delivers a wide output frequency range from 0 to 599 Hz. As a result, it suits many industrial machines that need precise adjustments.

Technical Specifications

The 13F5A3D-YA0H inverter provides robust electrical performance. Below are the key parameters:

• Input AC Phase: AC 3 PH 50/60 Hz

• Input Voltage: 400V

• Input Current: 16.8 A

• UL Input Voltage: 480V

• UL Input Current: 15.4 A

• Output AC Phase: AC 3 PH

• Output Current: 12 A

• UL Output Current: 11 A

• Output Frequency: 0 to 599 Hz

• Output Power: 8.3 kVA

• Output Voltage Value: 0 to Uin (same as input level)

Moreover, the apparent power rating of 8.3 kVA guarantees a stable electricity supply. The drive also maintains high efficiency across different loads. For complex machinery, this means fewer interruptions and lower energy costs.

Mechanical & Environmental Parameters

This inverter is built for industrial durability. Its enclosure protects against dust and minor moisture. The operating temperature ranges from -10°C to +50°C. Furthermore, it can handle humidity levels up to 90% without condensation. Storage temperature goes from -25°C to +70°C. The unit also resists vibration according to IEC 60068-2-6 standards. Consequently, it performs well in sawing, cutting, and material handling systems.

Installation Guidelines

Installing the KEB 13.F5.A3D-YA0H requires basic electrical knowledge. First, disconnect all power sources before starting. Mount the inverter vertically on a non-flammable surface. Ensure at least 100 mm of free space above and below for cooling. Next, connect the three-phase input wires to terminals L1, L2, and L3. Then attach the motor wires to U, V, and W output terminals. Use shielded cables for lengths over 10 meters. Finally, set the parameters according to your motor nameplate. For HOLZMA saws, refer to the original wiring diagram. Meanwhile, check all connections twice before powering up.

Why Choose This Drive for HOLZMA Equipment?

The KEB 13F5A3D-YA0H is a direct fit for HOLZMA beam saws. Models like HPL380, HPP350, and 180 benefit from its precise frequency control. Specifically, the drive reduces mechanical stress during start and stop cycles. It also improves cutting accuracy by maintaining steady torque. Besides that, the inverter's overload protection extends motor life. Therefore, maintenance costs go down over time. Many users also report quieter operation compared to older drives. For factory managers, this means higher productivity and less downtime.

Frequently Asked Questions (FAQ)

1. Can the KEB 13F5A3D-YA0H work with a single-phase input?
No, this drive requires a three-phase AC input of 400V. Single-phase operation is not supported.

2. What happens if the output frequency exceeds 599 Hz?
The KEB 13.F5.A3D-YA0H is limited to 599 Hz. Exceeding this may trigger an overfrequency fault and stop the output.

3. Is this inverter compatible with non-HOLZMA machines?
Yes, it works with any three-phase induction motor rated for 400V and 8.3 kVA or less. However, parameter adjustments will be needed.

4. How do I reset a fault on the 13F5A3D-YA0H?
Press the reset button on the keypad for 2 seconds. Alternatively, cycle the main power off for 30 seconds.

5. What is the recommended cable size for input power?
Use 2.5 mm² (14 AWG) copper wire with 75°C insulation. For longer runs above 20 meters, use 4 mm² (12 AWG).